Did you get the ddc 18watt pump and the PA120.3 rad?
Printable View
Did you get the ddc 18watt pump and the PA120.3 rad?
Same pump and rad as mine. I got the ek ddc top. Where you putting the rad...its huge? or will it fit where your existing one is m8?
I have a triple in at the moment :
http://i472.photobucket.com/albums/r...g?t=1222197177
http://img87.imageshack.us/img87/5397/dsc02307.jpg
So length / width wise it should be fine
The new rad is approx 25mm deeper so may be tight under the case, may have to look at some mods to raise the case slightly :D
I was more concerned of the thickness, but looks like you have plenty room underneath. :)
Well all the parts are here, the old rig is stripped and drained down.
New Pump / res in place and the rad flushed and barbed up :P
The new rad is slightly longer and the fixing positions different to the last rad, so (hopefully tonight) ill be introducing Mr.Jigsaw and Mr.Drill to my case again to make things line up.
Unfortunately the rad came without fixing screws (Thermochill were extremely helpful and apologetic) and they are in the post today :D
So, all going well, I should be hopefully up and running by the end of the weekend / early next week some some pics of the ne setup.
Cheers
TB
Nice 1 tb....pics?...i got 11 screws instead of 12. had to order more from chilled pc.
I took a pick of the mobo tray with everything plumbed in waiting to go back in the case once the bottom is "adjusted" :P and the screws arrive - ive run out of memeory on the camera and need my PC up and runing to dowload the pics :S
As soon as im set up i'll get them posted
:D
Right, so finally got the parts and being swapping the kit over for the last few days - still have some bits and bobs (cable management and a few other things) to sort out, but here we go ............
Got the new pump attached to the mobo tray and all plumbed up ....
http://img24.imageshack.us/img24/7972/incase.jpg
Losing the bay res has freed back up enough room to get a 120mm fan in the front of the case, which now looks like this (the door is not fitted on this shot):
http://img22.imageshack.us/img22/7161/frontdne.jpg
Some of the inside with it all filled up and ready to go
http://img22.imageshack.us/img22/7118/incase1.jpg
http://img144.imageshack.us/img144/3375/incase2.jpg
http://img24.imageshack.us/img24/5898/incase3.jpg
Now for the temps .............
I was idling around mid 30s @ 3.6 - bearing in mind the general temperature (weather wise) has gone up a few degrees over the last few days, im quite happy with these:
http://img17.imageshack.us/img17/3770/idle.png
Under load I was getting high 60s (sometimes into the 70s) with a core dropping
http://img4.imageshack.us/img4/7807/tb3hours.png
Ive solved the core dropping by adjusting the the voltages and my Prime temps have dropped by quite a bit:
http://img26.imageshack.us/img26/2977/loadn.png
And passes five IBT tests at max temp of 77 :D
http://img144.imageshack.us/img144/4110/tbibt.png
So all in all my temps have seen a good drop, I like the set up better and jobs a good um, ill get some pics in the dark with teh UV on later
Ta
TB
Looking awesome mate :up:
Cheers :D
Temps are a bit better this morning with lower ambients :
http://img6.imageshack.us/img6/9485/mooningtemps.png
And some from last night:
http://img4.imageshack.us/img4/8953/uv3.jpg
http://img27.imageshack.us/img27/8438/uv2.jpg